Water level indicator Circuit

tank-water-level-indicator-with-alarm-circuit-diagram-transistors

Wastage of water is really an issue in places where they use overhead tanks. Monitoring of water level is really a difficult task in those places and it could also lead to wastage of water and power. The above circuit shows a simple water level indicator system based on Tranistors and LED’s. This circuit could give a simple and cost effective solution for this problem. This circuit was  a simplified version of “Water level indicator” published in Instructables by Raikut.

WORKING OF CIRCUIT:

The circuit schematic comprises of totally two parts. Indicator section for indicating the water level present in the tank and Alarm section for alerting the people to turn off the pump once the tank is completely filled. The LED’s are used for indicating the level whereas the transitors are used as a switching devices. A simple buzzer was used to sound provide the overflow warning. This circuit works based on the conductive property of the water.

The positive line of 6V is inserted into the tank, when there is no water in the tank all the three transistors will be in off state. When the water pump is turned on water starts filling the tank, when the water reaches the 1/4 level of the tank it comes in contact with the 1/4th level wire which is connected to the base of the transistor Q1. The water will provide a path for the current to flow from supply to the base of the terminal. This turns the tranistor Q1 in turn Red LED D1 which indicates that 1/4th level of tank is filled with water.

In the same way when the water reaches the 1/2th level it turns on yellow LED and when the tank is full it turns on the green LED. By this way the LED’s help us to determine the level of water in the tank. Coming to the alarm section when the tank is full it turns the transistor Q4 which was wired as a switch to turn on the Buzzer which alerts the person to turn off the pump in order to avoid overflow of tank.

The switch given was used to turn off the alarm after the person is alerted. But do remember to turn the switch on before turning the Pump on or else the alarm won’t work. For advanced version of this circuit refer to this article “Water Level Indicator Circuit with Alarm on Instructables”.

NOTE:

  • You can increase various stages of water level by increasing the number of transitors and LED’s in the circuit. 
  • Try Using different colors of LED to avoid confusion or use a marker to write the appropriate water level near the LED’s.

13 Comments

  1. Anonymous

    what is the function of that 100ohm resistor to the base

    what if is i decide to use less than or greater than that

    Reply
    1. Frank DonaldFrank Donald (Post author)

      It will limit the base current to turn the transistor ON. I suggest you to use the value shown in the diagram

      Reply
  2. Tejas

    What is the purpose of the 10k resistor connected across base-emitter of each transistor?
    To increase input resistance? What will happen if I don’t use it?

    Reply
    1. Frank DonaldFrank Donald (Post author)

      Hi Tejas,
      It’s called as pull down resistor. It’s function is to feed voltage 0 to base of transistor whenever there is no voltage input from the wire dipped in water tank.

      Reply
      1. Tejas

        Got it! Thank you!

        Reply
        1. Frank DonaldFrank Donald (Post author)

          Welcome

          Reply
  3. M.I. Fco. Javier Rodríguez G.

    What about corrosion in the electrodes? They won’t last four so long.

    Reply
    1. Frank Donald

      That will be a great concern in this system am not gonna deny that. But cost wise this could give a good solution for the water wastage. We will try to post better Water level sensing circuits and keep you updated. Thank you, keep visiting.

      Reply
  4. cf2a394a-759f-11e4-9f4b-73366eb7928c

    The system has a pressure sensor, a quad op-amp indicator LED’s, reference pots, and eleven resistors. An audible alarm can be added with a resistor, transistor and audible buzzer. The advantage is that this system will work in any kind of liquid and has no contact with the liquid. A tube connected to the pressure sensor, runs from the top of the tank to the bottom of the tank. As the liquid level rises, the pressure in the tube increases. The two op-amp differential input stage, amplifies the pressure sensor input. The other two op-amps compare the sensor voltage to a reference voltage to indicate the level. If more indicator levels are needed, a dual or quad op-amp can be added to indicate additional levels. Ron H.

    Reply
    1. Frank Donald

      Great idea Ron, you are the best. When i find this circuit i thought this could do a good job with minimal cost but your idea will do a lot better job than this one.

      Reply
  5. cf2a394a-759f-11e4-9f4b-73366eb7928c

    The only problem with this kind of level detector is: 1. the fluid must be ionic to conduct current. If the fluid is an oil or an an-ionic liquid, this circuit won’t work. 2. the DC current will cause the sense electrodes to de-plate and eventually disappear which will cause failure. using AC is the correct way to avoid deplating. 3. This design requires a separate electrode for each level detected. There is a much better way to do this using a pressure sensor and a quad op-amp to measure the depth. If anyone is interested, I will provide a circuit for accomplishing the task. Regards, Ron H.

    Reply
    1. Frank Donald

      We are definitely interested. Adding pressure sensor will make the system complex won’t it???

      Reply
      1. alejandro

        not necesarilly, depending on the sensor, and you can always add comparators (schmit trigger like) to turn on/off the leds

        Reply

Leave a Comment

Your email address will not be published. Required fields are marked *